HKS 86(ZN6) Product lineup (To be developed.)

*The list below shows products to be developed. Product lineup is subjected to change.

We have been very hard at work here at AVO, and we are starting to roll out the parts for the new Subaru BRZ and Toyota FRS! Suspension parts and here and ready to go, and inlets are rolling out of the factory now. Get your orders in!

	BRZ Silicone Inlets and Sound Tubes are now here! Available in Black, Red, and Blue (as pictured). We are taking pre-orders now on our initial run from the factory. Part Numbers: S6Z12E4POBLKJ - Black Silicone Inlet S6Z12E4P6BLKJ - Black Silicone Sound Tube S6Z12E4POBLUJ - Blue Silicone Inlet S6Z12E4P6BLUJ - Blue Silicone Sound Tube S6Z12E4POREDJ - Red Silicone Inlet S6Z12E4P6REDJ - Red Silicone Sound Tube
	The AVO high-flow pop-in panel air filter for BRZ has been designed specifically for the Subaru models. Made from sturdy cotton fiber, it increases air flow, allowing the engine to make more power and torque. Yet thanks to a special dry film it has equal rates of engine protection. This dry film design does not use oil, like most other performance filters, which keeps your MAF from being damaged from excess oil. Thanks to it's high-tech design the AVO panel air filter is washable, extending the life beyond your standard drop-in air filter. You simply need to soak it in warm, soapy water, rinse it out with water, then let it air dry. Part Number: S6Z12E43A001T
	The standard offset Caster Adjustment Bushing replaces the big, squishy tennis ball that the front suspension pivots on with a harder polyurethane bushing. Despite the welcome increase in rigidity and decrease in movement, NVH changes very little. Positive offset caster increases turn-in and straightline stability. Part Number: +0.00 Offset: S1X03E1GV002T +0.05 Offset: S1X03E1GV001T
	Heavy duty AVO adjustable rear endlinks are a significant upgrade from the standard endlinks. The standard endlinks are quite slender, and are prone to bending when a performance rear stabilizer bar is fitted. And if you change the height of the car's suspension, you may end up with issues with the rear stabilizer bar being pushed up too high, affecting the effectiveness of the rear bar. Our adjustable rear endlink allows you to not only fine-tune the rear bar setup, but is much stronger as well. Polyurethane bushings at the bottom help remove unwanted movement, and the upgraded ball-joint is stronger as well. Part Number: S2C07G1HU001J
	Upgraded bushings will cut the slop out of your handling by replacing the soft rubber with much stronger Polyurethane. Designed to fit the standard stabilizer bar mounting bracket. Available in size from 18mm to 23mm. Part Number: S2C07G1HV0** ** = size
	This Polyurethane bushing is a replacement for the soft rubber bushing at the front inside corner of the front Lower Control Arm (LCA). This is a relatively simple job, especially if you do it at the same time as the CAB bushing for the rear of the front LCA. Part Number: S2C08G1GV057T
	The AVO rear suspension mount reinforcement bracket corrects a significant weak point on the BRZ and FRS. The standard stabilizer mount point is very flexible, and has been known to break when stronger rear stabilizer bars are fitted. Or even with standard rear stabilizer bars when the car is driven too sportily! The AVO mount fixes this problem in an elegant manner, and is compatible with any rear stabilizer bar that uses the standard rear bracket, including the AVO stabilizer bar upgrades. Part Number: S6Z12E1HT001T
	The AVO DBW Throttle Controller allows you to re-map your throttle inputs to the throttle body controller, giving you full control over it's behaviour. You may have noticed with your DBW car that the position of the gas pedal doesn't necessarily correspond to the throttle response. This is because the factory settings are a non-linear map that decides what's optimal for their needs, not yours. The AVO DBW Throttle controller brings back that control over your car. Part Number: S2A08G69I001J
	Find us on Facebook!

The new 86 MODELLISTA VERSION

GReddy FR-S / BRZ / GT86 / 86 Products >

>EXHAUST SYSTEMS  
(more info)  
>10117202    SP Elite 60mm Exhaust   NEW!
    >                      ^{(axle-back, sideways muffler, dual tips)}    >1011730X    Evo3 70mm Exhaust    >                       ^{(large diameter, dual muffler system)}    >1011710X    RS Racing Sport Exhaust    >                       ^{(large diameter, single exit, driver side)}    > 

INTAKE SYSTEMS
>12519101    GReddy Air Intake System    >                          ^{(with Momentum Air Box)}  

COOLING SYSTEMS
>12014632     10 row Oil Cooler Kit   (special order)

12002802      Oil Block Attachement  

SUSPENSION SYSTEMS
>   TBA           Type-S Coil-over Kit    >                                  

AERO SYSTEMS   >   
TBA          GReddy X Rocket Bunny  Aero Kit               >                         ^{(GReddy Exclusive)}          

ACCESSORIES
>GT31129_1     GReddy Drift FR-S T-Shirt >                             ^{(premium black tee)}     >1851010_       Carbon Hood Damper Set      >                             ^{(oem weight hood lifter)}      >14401XXX      GReddy Racing Lug Nuts     >                             ^{(M12xP1.25 - Short, Long or Locks)}